bkaii.com.vn BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!

SR-1000-SFP: Bộ chuyển đổi quang điện Gigabit Copper to Fiber Converter

Giá: Liên hệ

SR-1000-SFP Bộ chuyển đổi Quang điện Gigabit Copper to Fiber Converter của hãng Perle hiện đang được BKAII phân phối rộng rãi tại thị trường Việt Nam. SR-1000-SFP được thiết kế theo tiêu chuẩn công nghiệp, nhỏ gọn, dễ dàng lấy được tín hiệu về PLC, máy tính, vi xử lý, máy tính nhúng. Sản phẩm hiện đang được sử dụng trong các bài toán M2M, IoT của các lĩnh vực: Điện lực, khí tượng thủy văn, giao thông thông minh…

Bộ chuyển đổi Quang điện

Tính năng của sản phẩm:

1000Base-T to 1000Base-X Fiber Media Converter
Link copper to multimode or single mode fiber
Empty slot for Cisco and other industry standard SFPs
Advanced Features: Link Pass-Through, Far-End Fault, Auto-MDIX
Triple Power Input: Dual Terminal block power connector & T-Bus

Thông số kỹ thuật của sản phẩm:

Power
Input Supply Voltage	Triple voltage 12 / 24 / 48 VDC (9.6 – 60 VDC) input supporting: a) 2 x Terminal Block power input and b) 1 x T-Bus power input
Current	0.09 A (@ 24VDC)
Power Consumption	2.16 watts (@ 24VDC)
Power Connector	Dual input Terminal Block and/or T-Bus
Indicators
Power / TST	This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink fast/slow when in Loopback test mode or hardware error.
Fiber link on / Receive activity (LKF)	On: Fiber link present. Blinking slowly: Fiber link disabled because of copper link loss. Blinking quickly: Fiber link present and receiving data. Off: No fiber link present
Copper link on / Receive activity (LKC)	On: Fiber link present. Blinking slowly: Fiber link disabled because of copper link loss. Blinking quickly: Fiber link present and receiving data. Off: No fiber link present
Switches - accessible by sliding the chassis open

Auto-Negotiation	Auto (Deafault-Up): In this mode of operation the media converter will negotiate Ethernet parameters on both the copper and the fiber connection. This will ensure the most optimal connection parameters will be in effect. If connecting to another Perle Gigabit Media Converter, this parameter should be set to Auto. Off: The fiber Negotiation should only be turned off, if the fiber link partner does not support fiber link negotiations
Smart Link Pass-Through	Standard Mode (Default-Up): In this mode, if Fiber Negotiation is set to OFF, the links on the fiber and copper sides can be brought up and down independently of each other. A loss of link on either the fiber link or copper link can take place without affecting the other connection. However, if the Fiber Negotiation (switch 2) is set to Auto, then a loss of link on the copper side will result in a loss of link on the fiber side but not vice versa. Smart Link Pass-Through (Down): In this mode, the link state on one connection is directly reflected through the media converter to the other connection. If link is lost on one of the connections, then the other link will be brought down by the media converter.
Pause	Enabled (Default-Up): In this mode, when Fiber Negotiation has been turned off, the media converter will use this setting for its Ethernet parameter negotiation on the copper connection. With this Pause switch in the Enabled position, the media converter will advertise support for Symmetrical and Asymmetrical Pause. Disabled: The media converter will not advertise support for the Pause feature.
Loopback	Disabled (Default-Up): The loopback feature is disabled. This is the normal position for regular operation. The switch must be set to this position for data to pass through the media converter. Enabled: This is a test mode. All data received on the receive (RX) fiber connection is looped back to the transmit (TX) fiber connection. The state of the copper is not relevant and no data or link status is passed through to the copper side.
Fiber Fault Alert (FFA)	Enabled (Default-Up): In this mode, when Fiber negotiation is turned on, if the media converter detects a loss of fiber signal on the fiber receiver it will immediately disable its fiber transmitter signal. This notifies the fiber link partner that an error condition exists on the fiber connection. If the remote media converter is set up for FFA Enabled and the local media converter is set up with Smart Link Pass-Through, a loss of fiber link on either the transmit or receive line will be passed through to the local copper connection to notify the connected device. If the media converter has been set to Smart Link Pass-Through mode, the effect will be the same as FFA since the link loss on the fiber receiver will result in bringing down the copper link, which will in turn cause the transmit fiber link to be brought down. Disabled: In this mode, the media converter will not monitor for fiber fault.
Duplex Mode	Auto (Default-Up): In this mode, when Fiber Negotiation has been turned off, the media converter will use this Duplex setting for its Ethernet parameter negotiation on the copper connection. In the Auto position, the media converter will advertise support for both Full and Half Duplex mode. The resultant negotiation will provide the most optimum connection. Half: In this mode, the media converter will force the negotiation to Half Duplex mode
Cables and Connectors
1000Base-T	RJ45 connector, 4 pair CAT 5 (UTP or STP) or better cable
Small Form Factor Pluggable ( SFP ) slot	SFP slot models: Empty slot for 100Base-X SFP modules supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs. Hot insertion and removable ( hot swappable ).
Magnetic Isolation	1.5kv
Fiber Optic Cable	Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron Single Mode: 9/125 micron (ITu-T 625)
Filtering
Filtering	1024 MAC Addresses
Frame Specifications
Buffer	1000 Kbits frame buffer memory
Size	Maximum frame size of 10,240 bytes
Packet Transmission Characteristics
Bit Error Rate (BER)	-12
Environmental Specifications
Operating Temperature	-10 C to 60 C (14 F to 140 F)
Storage Temperature	-25 C to 70 C (-13 F to 158 F)
Operating Humidity	5% to 90% non-condensing
Storage Humidity	5% to 95% non-condensing
Operating Altitude	Up to 3,048 meters (10,000 feet)
Heat Output ( BTU/HR )	7.37
MTBF (Hours)	696,927 (Calculation model based on MIL-HDBK-217-FN2 @ 30 °C)
Chassis	Molded plastic DIN Rail case with an IP20 ingress protection rating
Mounting
Din Rail Kit	Native
Product Weight and Dimensions
Weight	0.12 kg, 0.26 lbs
Dimensions	114 x 100 x 22.5mm, 4.5 x 3.9 x 0.88 inches
Packaging
Shipping Weight	0.17 kg, 0.37 lbs
Shipping Dimensions	145 x 105 x 30 mm, 5.7 x 4.1 x 1.2 inches

Các bài viết tham khảo:

"BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!

Downloads sr-1000-installation-guide-bkaii.pdf