RUT200: Router công nghiệp 4G Teltonika

4G LTE Cat 4 up to 150 DL/50 UL Mbps; 3G up to 21 DL/5.76 UL Mbps; 2G up to 236.8 DL/236.8UL kbps

Consumer type eSIM, profile download and removal operations, up to 7 eSIM profiles; does not include data plans. Feature availability varies by order code

1 x 2FF SIM and 1x eSIM, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail

IMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength RSSI, SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC

SMS status, SMS configuration, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

Supports sending and reading Unstructured Supplementary Service Data messages

Operator block/allow list (by country or separate operators)

Possibility to use different PDNs for multiple network access and services

Band lock, Used band status display

SIM PIN code management enables setting, changing, or disabling the SIM card's PIN

Direct connection (bridge) between mobile ISP and device on LAN

Router assigns its mobile WAN IP address to another device on LAN

802.11b/g/n Wi-Fi 4, Access Point AP, Station STA

WPA2 Enterprise: PEAP, WPA2 PSK, WPA EAP, WPA PSK, WPA3 SAE, WPA3 EAP, OWE; AES CCMP, TKIP, Auto-cipher modes, client separation, EAP TLS with PKCS#12 certificates, disable auto-reconnect, 802.11w Protected Management Frames PMF

SSID stealth mode and access control based on MAC address

Up to 50 simultaneous connections

Wireless mesh 802.11s), fast roaming 802.11r), Relayd, BSS transition management 802.11v), radio resource measurement 802.11k)

Allowlist, blocklist

Once scanned, a user will automatically enter your network without needing to input login information

Forward Wi-Fi hotspot landing page to a subsequent connected device

1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX

1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX

Static routing, Dynamic routing BGP, OSPFv2, RIP v1/v2, EIGRP, NHRP, Policy based routing

TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan WOL, VXLAN

H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Port forward, traffic rules, custom rules, TTL target customisation

View all your Firewall statistics, rules, and rule counters

View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on

Visual representation of your network, showing which devices are connected to which other devices

Static and dynamic IP allocation, DHCP relay, DHCP server configuration, status, static leases: MAC with wildcards

Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

Supported 77 service providers, others can be configured manually

DNS over HTTPS proxy enables secure DNS resolution by routing DNS queries over HTTPS

Wi-Fi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover

Balance Internet traffic over multiple WAN connections

Possibility to mount remote file system via SSH protocol

Real-time monitoring, wireless signal charts, traffic usage history

Captive portal (hotspot), internal/external Radius server, Radius MAC authentication, SMS authorisation, SSO authentication, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customisable themes and optionality to upload and download customised hotspot themes

Pre-shared key, digital certificates, X.509 certificates, TACACS, Internal & External RADIUS users authentication, IP & login attempts block, time-based login blocking, built-in random password generator

Preconfigured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI, DMZ, NAT, NATT, NAT64

DDOS prevention SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention SYN FIN, SYN RST, X-mas, NULL flags, FIN scan attacks)

Port and tag-based VLAN separation

Mobile data limit, customizable period, start time, warning limit, phone number

Block list for blocking out unwanted websites, allow list for specifying allowed sites only

Flexible access control of SSH, Web interface, CLI and Telnet

Certificate creation tool allows to create CA, server, client, let's encrypt, SCEP certificates

Port-based network access control server

Multiple clients and a server can run simultaneously, 27 encryption methods

DES CBC 64, RC2 CBC 128, DES EDE CBC 128, DES EDE3 CBC 192, DESX CBC 192, BF CBC 128, RC2 40 CBC 40, CAST5 CBC 128, RC2 64 CBC 64, AES 128 CBC 128, AES 128 CFB 128, AES 128 CFB1 128, AES 128 CFB8 128, AES 128 OFB 128, AES 128 GCM 128, AES 192 CFB 192, AES 192 CFB1 192, AES 192 CFB8 192, AES 192 OFB 192, AES 192 CBC 192, AES 192 GCM 192, AES 256 GCM 256, AES 256 CFB 256, AES 256 CFB1 256, AES 256 CFB8 256, AES 256 OFB 256, AES 256 CBC 256

XFRM, IKEv1, IKEv2, with 14 encryption methods for IPsec 3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16

GRE tunnel, GRE tunnel over IPsec support

Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the programʼs code

Method of building scalable IPsec VPNs, Phase 2 and Phase 3 and Dual Hub support

SSTP client instance support

ZeroTier VPN client support

WireGuard VPN client and server support

Tinc offers encryption, authentication and compression in it's tunnels. Client and server support.

MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionality

8-bit: INT, UINT; 16-bit: INT, UINT MSB or LSB first); 32-bit: float, INT, UINT ABCD (big-endian), DCBA (little-endian), CDAB, BADC, HEX, ASCII

HTTP S, MQTT, Azure MQTT

Extract parameters from multiple sources and different protocols, and send them all to a single server; Custom LUA scripting, allowing scripts to utilize the router's Data to server feature

Allows sending commands and receiving data from MODBUS Server through MQTT broker

Station, Outstation

DLMS - standard protocol for utility meter data exchange

Expand your device's possibilities by using a set of configurable API endpoints to retrieve or change data.

HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, multiple event log servers, firmware update availability notifications, event log, system log, kernel log, Internet status

Firmware update from server, automatic notification

SMS status, SMS configuration

Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, Wi-Fi on/off

OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendlytech, AVSystem

MQTT Broker, MQTT publisher

SNMP (v1, v2, v3), SNMP Trap, Brute force protection

Management API over HTTP/HTTPS

Teltonika Remote Management System RMS

Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength. Has reboot and firmware upgrade actions

Can be configured with Data to Server to send all the available parameters to the cloud. Has Direct method support... Plug and Play integration... zero-touch device provisioning.

Utility to interact with the AWS cloud platform. Jobs Support: Call the device's API using AWS

Update FW/configuration for multiple devices at once

Update FW without losing current configuration

A full factory reset restores all system settings, including the IP address, PIN, and user data to the default manufacturer's configuration

RutOS OpenWrt based Linux OS

Busybox shell, Lua, C, C++

SDK package with build environment provided

You can create your own custom, branded firmware and web page application by changing colours, logos, and other elements in our firmware to fit your or your clientsʼ needs

The Package Manager is a service used to install additional software on the device

1 x Digital Input, 0 - 6 V detected as logic low, 8 - 30 V detected as logic high

1 x Digital Output, Open collector output, max output 30 V, 300 mA

Email, RMS, SMS

Allows to set certain I/O conditions to initiate event

4-pin industrial DC power socket

9 – 30 VDC, reverse polarity protection; surge protection 31 VDC 10us max

Passive PoE over spare pairs. Possibility to power up through LAN1 port, not compatible with IEEE 802.3af, 802.3at and 802.3bt standards, Mode B, 9 - 30 VDC

2 x RJ45 ports, 10/100 Mbps

1 x Digital Input, 1 x Digital Output on 4-pin power connector

3 x Connection type status LEDs, 5 x Connection strength LEDs, 2 x LAN status LEDs, 1 x Power LED

1 x SIM slot Mini SIM – 2FF, 1.8 V/3 V, external SIM holder

1 x 4-pin power connector

2 x SMA for LTE, 1 x RP SMA for Wi-Fi antenna connectors

Reboot/User default reset/Factory reset button

Aluminium housing, plastic panels

83 x 25 x 74 mm

DIN rail, wall mount, flat surface (all require additional kit)

10% to 90% non-condensing

CE, UKCA, RCM, EAC, Anatel, ANRT, Kenya, ICASA, NCC, ETA WPC, SIRIM, IMDA, NTC, NBTC, MTCNOM, E-mark, CB, RoHS, REACH, R118

EN 55032 2015 + A1 2020 EN 55035 2017 + A11 2020 EN IEC 61000 3 2 2019 EN 61000 3 3 2013 + A1 2019 EN 301 489 1 V2.2.3 EN 301 489 17 V3.2.4 EN 301 489 52 V1.2.1

EN 61000 4 2 2009

EN IEC 61000 4 3 2020

EN 61000 4 4 2012

EN 61000 4 5 2014 + A1 2017

EN 61000 4 6 2014

EN 61000 4 11 2020

EN 300 328 V2.2.2 EN 301 511 V12.5.1 EN 301 908 1 V15.1.1 EN 301 908 2 V13.1.1 EN 301 908 13 V13.1.1

CE: EN IEC 62368 1 2020 + A11 2020, EN IEC 62311 2020, EN 50665 2017 RCM: AS/NZS 62368.1 2022 CB: IEC 62368-1 2018