bkaii.com.vn BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!

SMI-10GR-STS: Managed Media Converters 1G to 10G Fiber and Rate Converters

Giá: Liên hệ

SMI-10GR-STS Managed Media Converters 1G to 10G Fiber and Rate Converters của hãng Perle hiện đang được BKAII phân phối rộng rãi tại thị trường Việt Nam. SMI-10GR-STS được thiết kế theo tiêu chuẩn công nghiệp, nhỏ gọn, dễ dàng lấy được tín hiệu về PLC, máy tính, vi xử lý, máy tính nhúng. Sản phẩm hiện đang được sử dụng trong các bài toán M2M, IoT của các lĩnh vực: Điện lực, khí tượng thủy văn, giao thông thông minh…

Bộ chuyển đổi tín hiệu Quang điện

Tính năng của sản phẩm:

Fiber to Fiber, copper to fiber and copper to copper conversion
Conduct 1G to 10G rate conversion
2 empty slots that use a variety of transceivers supplied by Perle, Cisco or other MSA compliant SFP+ and XFPs
Advanced features: Cut-Through Forwarding, Smart Link Pass-Through, Fiber Fault Alert, Built-in Link Test Generator and Loopback
Support for Power Level 1 and 2
Optical signal regeneration: 3R (re-amplify, reshape, and retime)
Manage via SNMP, CLI - Telnet/SSH, Internet browser, or PerleVIEW Centralized Management Package

Thông số kỹ thuật của sản phẩm:

Power
Input Supply Voltage	12 vDC Nominal
Maximum Current Amps @ 12v DC	0.8
Maximum Power * Requirements	19.5 watts*
Power Connector	5.5mm x 9.5mm x 2.1mm barrel socket
Power Adapter
Universal AC/DC Adapter	100-240v AC, regulated AC/12v DC adapter included 12 watt adapter
Indicators
Power / TST	On: Power indication and in normal operation Blinking slowly: the unit is in loopback or test mode (either port) Blinking quickly: the unit has a hardware error (Err LED will also be on)
LK1, LK2	On: Fiber link present Blinking quickly: Fiber link present and receiving data.(including test data) Blinking slowly: Fiber link disabled because the other fiber link went down. Blinking 1 sec on 3 sec off – invalid SFP+ inserted Blinking twice then 3 sec off – module shut down due to high temperature. LK1, LK2 alternating on and off – 1 sec on 1 sec off incompatible Speeds ( Err LED will also be on) Off: No fiber link present or no module inserted
ERR LED	When in test mode – this indicates test mode errors – will clear when the link has recovered If Power LED is blinking, this indicates a hardware error If LNK LEDS blink, this indicates that there is a module compatibility error
Switches - accessible through a side opening in the chassis
Smart Link Pass-Through	Enabled (Default - Up) When the Smart Link Pass-Through switch is enabled (default), each port will reflect the state of its port peer. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS. When the switch is in the down position, Smart Link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port.
Fiber Fault Alert	Enabled (Default - Up) With Fiber Fault Alert the state of the 10 Gigabit ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G ethernet interface of the media converter.
Cut-through / Rate converting	Rate Converting (Default - Up) The Media Converter can automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different. When the same Ethernet speed for both ports is enabled, the Media Converter can be configured for Cut-Through Forwarding. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible. Forwarding of a packet will begin as soon as the destination address is processed
Fiber Interface Loopback	Disable (Default - Up) When enable, the media converter will be in fiber loopback mode. In this mode all frames received on the fiber port will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link
Loopback Interface	Port 1(Default - Up) In this mode, all frames received on the fiber port 1 in loopback mode will be transmitted back. When switch is set down, port 2 will be in loopback mode and transmitting all frames received back.
Connectors – Two SFP / SFP+ Transceiver Slots. Hot insertion and removable.
Supported 10 Gigabit Fiber SFP+ transceivers	Power Levels 1 and 2 IEEE 802.3ae compliant: 10GBase-SR 10GBase-LRM 10GBase-LR 10GBase-ER 10GBase-ZR CWDM/DWDM
Supported 1 Gigabit Copper SFPs	1000Base-T 1000Base-T SGMII
Supported Gigabit Fiber SFPs	Standard SFP Power level 1 (1 watt) and level 2 (1.5 watts) as per SFP-8431 1000Base-SX 1000Base-LX/LH 1000Base-EX 1000Base-ZX 1000Base-BX CWDM/DWDM
Environmental Specifications
Operating Temperature	0° C to 50° C (32° F to 122° F)
Storage Temperature	minimum range of -25° C to 70° C (-13° F to 158° F)
Operating Humidity	5% to 90% non-condensing
Storage Humidity	5% to 95% non-condensing
Operating Altitude	Up to 3,048 meters (10,000 feet)
Heat Output ( BTU/HR )	67
MTBF (Hours)	Without power adaptor: 132,947 With power adaptor: 92,122 Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Chassis	Metal with an IP20 ingress protection rating
Mounting
Din Rail Kit	Optional
Wall / Rack Mount Kit	Optional
Product Weight and Dimensions
Weight	0.93 Kg, 2.1 lbs
Dimensions	175 x 145 x 46mm, 6.9 x 5.7 x 1.8 inches

Mã sản phẩm:

SMI-10GR-STS - Managed 10 Gigabit Media and Rate Converter with dual SFP+ slots (empty). Includes AC power Adapter

Các bài viết tham khảo:

"BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!