bkaii.com.vn BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!

CM-100MM: Managed Fast Ethernet 100Base-FX to 100Base-X Fiber Mode Conversion

Giá: Liên hệ

CM-100MM Managed Fast Ethernet 100Base-FX to 100Base-X Fiber Mode Conversion ( Single Fiber Models ) của hãng Perle được BKAII đang phân phối rộng rãi tại thị trường Việt Nam. CM-100MM được thiết kế theo tiêu chuẩn công nghiệp, nhỏ gọn, dễ dàng lấy được tín hiệu về PLC, máy tính, vi xử lý, máy tính nhúng. Sản phẩm hiện đang được sử dụng trong các bài toán M2M, IoT của các lĩnh vực: Điện lực, khí tượng thủy văn, giao thông thông minh, hệ thống kiểm soát an ninh…

Bộ chuyển đổi Quang điện

Tính năng của sản phẩm:

100Base-FX to 100Base-X Fiber to Fiber Media Converter Module
Multimode to multimode or multimode to single mode
Extend multimode fiber to 120km ( or more through chaining )
Choice in SC, LC and ST fiber connector models
Signal regeneration prevents signal degradation
Advanced Features: Link Pass-Through, Far-End Fault, loopback for each fiber connection
High density applications with Perle Media Converter Chassis
Manage via SNMP, CLI - Telnet/SSH, Internet browser, or
PerleVIEW Centralized Management Package with an
MCR-MGT Media Converter Management Module

Thông số kỹ thuật của sản phẩm:

Indicators
Power / TST	This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.
Fiber link 1 / Receive activity (LK1)	This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.
Fiber link 2 on / Receive activity (LK2)	This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.
Switches: On-Board (If Auto/Switch strap is set to Switch)
Link Pass Through	Enabled (Default) - When the state of the receiver is changed on one of the 100Base-X interfaces it is reflected on the other 100Base-X fiber transmitter. When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on. If disabled , the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.
Far-End Fault (FEF)	Enabled (Default) - The media converter transmits the Far-End Fault Indication over the fiber connection whenever a receive failure is detected. The media converter continuously monitors the fiber connection and clears the Far-End Fault Indication condition when a valid signal is received. When Disabled, Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-X fiber connection.
Remote Loopback #1	The media converter can perform a loopback on the link #1 fiber interface. Disabled (Default - Up) Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. Link #2's fiber transmitter is taken off the interface.
Remote Loopback #2	The media converter can perform a loopback on the link #2 fiber interface. Disabled (Default - Up) Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. Link #1's fiber transmitter is taken off the interface.
Configuration Mode (Strap)	Auto (default) enable management module to overwrite hardware switch settings Switch - Use onboard DIP switches
Cables
Fiber Optic Cable	Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron Single Mode: 9/125 micron (ITU-T 625)
Packet Transmission Characteristics
Bit Error Rate (BER)	-12
Environmental Specifications
Operating Temperature	0 C to 50 C (32 F to 122 F)
Storage Temperature	minimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity	5% to 90% non-condensing
Storage Humidity	5% to 95% non-condensing
Operating Altitude	Up to 3,048 meters (10,000 feet)
Heat Output ( BTU/Hr )	11.9
Maximum Power Consumption ( Watts )	3.5
MTBF (Hours)*	484,202
Product Weight
Weight	0.15 kg, 0.33 lbs

Mã sản phẩm: Single Fiber Models

Model	Port	Connector	Type	Transmit (dBm)		Receive (dBm)		Power Budget (dBm)	Wavelength (nm)	Fiber Type	Operating Distance
Model	Port	Connector	Type	Min	Max	Min	Max	Power Budget (dBm)	Wavelength (nm)	Fiber Type	Operating Distance
CM-100MM-S1ST20U	Port 1	Dual ST	100BASE-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
CM-100MM-S1ST20U	Port 2	Single ST	100BASE-BX	-14.0	-8.0	-32.0	-3.0	18.0	1310/1550	SMF	20 km (12.4 mi)
CM-100MM-S1ST20D	Port 1	Dual ST	100BASE-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
CM-100MM-S1ST20D	Port 2	Single ST	100BASE-BX	-14.0	-8.0	-32.0	-3.0	18.0	1550/1310	SMF	20 km (12.4 mi)
CM-100MM-S1SC20U	Port 1	Dual SC	100BASE-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
CM-100MM-S1SC20U	Port 2	Single SC	100BASE-BX	-14.0	-8.0	-32.0	-3.0	18.0	1310/1550	SMF	20 km (12.4 mi)
CM-100MM-S1SC20D	Port 1	Dual SC	100BASE-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
CM-100MM-S1SC20D	Port 2	Single SC	100BASE-BX	-14.0	-8.0	-32.0	-3.0	18.0	1550/1310	SMF	20 km (12.4 mi)
CM-100MM-S1SC40U	Port 1	Dual SC	100BASE-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
CM-100MM-S1SC40U	Port 2	Single SC	100BASE-BX	-8.0	-3.0	-33.0	-3.0	25.0	1310/1550	SMF	40 km (25 mi)
CM-100MM-S1SC40D	Port 1	Dual SC	100BASE-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
CM-100MM-S1SC40D	Port 2	Single SC	100BASE-BX	-8.0	-3.0	-33.0	-3.0	25.0	1550/1310	SMF	40 km (25 mi)

Các bài viết tham khảo:

"BKAII -Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!"

IDS-509GPP: Switch công nghiệp PoE+ hỗ trợ 9 cổng Quang tốc độ Gigabit

Giá: Liên hệ

IDS-509GPP Switch công nghiệp PoE+ hỗ trợ 9 cổng Quang tốc độ Gigabit&n...

CM-100MM: Managed Fast Ethernet 100Base-FX to 100Base-X Fiber Mode Conversion

Bài viết mới cập nhật...

Số lượng người đang truy cập...

Catalog online

FIND US ON: