bkaii.com.vn BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!

eX-CM1110: Managed Gigabit Ethernet Extender Modules Managed Long Range LAN Extender

Giá: Liên hệ

eX-CM1110 Managed Gigabit Ethernet Extender Modules Managed Long Range LAN Extender của hãng Perle hiện đang được BKAII phân phối rộng rãi tại thị trường Việt Nam. eX-CM1110 được thiết kế theo tiêu chuẩn công nghiệp, nhỏ gọn, dễ dàng lấy được tín hiệu về PLC, máy tính, vi xử lý, máy tính nhúng. Sản phẩm hiện đang được sử dụng trong các bài toán M2M, IoT của các lĩnh vực: Điện lực, khí tượng thủy văn, giao thông thông minh…

Bộ chuyển đổi Quang điện

Tính năng của sản phẩm:

For use in high-density applications with Perle Converter Chassis
Extends 10/100/1000Base-T Ethernet up to 10,000 feet ( 3 KM ) over 2-wire 24 AWG twisted pair.
High-Speed – up to 200+ mbps aggregate bandwidth
Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes.
Advanced features - Link Pass-Through, Interlink Fault Feedback, Auto-MDIX and Loopback
Manage via SNMP, CLI - Telnet/SSH, Internet browser, or PerleVIEW Centralized Management Package with an MCR-MGT Media Converter Management Module

Thông số kỹ thuật của sản phẩm:

Ethernet
Port	1 port RJ45 – 10/100/1000 Base-T - Shielded
Auto-MDIX	Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance	Distance up to 100 meters ( 328 feet ) as per IEEE 802.3
Maximum Frame Size	1522 bytes

VDSL – Interlink

RJ45, BNC, Terminal Block

Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.

TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:

RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
BNC – Coaxial 50 and 75 ohm cable with BNC connector
Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ).

Chassis Module
Compatible chassis	Module occupies a single slot in Perle Converter Chassis
Indicators
Power / TST	This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local	Ethernet Extender is operating in CO VDSL mode
CPE - remote	Ethernet Extender is operating in CPE VDSL mode
ILNK	Indicates Link Status and activity on the Interlink (VDSL) port
ETH	Indicates link status and activity on Ethernet port.
Switches – On-board PCB
Rate/Reach	Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio	Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u)	Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex. Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Link Mode	Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer. Link Pass-Through- the state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.
Interlink Fault Feedback	Enabled - A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers Disabled ( Default ) – The state of the VDSL link is not propagated to the 10/100/1000Base-T port
Loopback	Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer. Disabled (Default - Up)
Set Ethernet Speed	When Auto-Negotiation switch is disabled, fixed speed can be set at 100 (Default) or 10
Set Ethernet Duplex	When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default or Half
Environmental Specifications
Operating Temperature	0 C to 50 C (32 F to 122 F)
Storage Temperature	minimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity	5% to 90% non-condensing
Storage Humidity	5% to 95% non-condensing
Operating Altitude	Up to 3,048 meters (10,000 feet)
Heat Output ( BTU/HR )	13.1
Power Consumption ( Watts )	3.8
MTBF (Hours)*	466,387

Mã sản phẩm:

eX-1CM1110-RJ - Managed Gigabit Ethernet Extender Module - 1 port 10/100/1000Base-T (RJ-45). RJ45 Interlink ( VDSL2 ) connector
eX-1CM1110-BNC - Managed Gigabit Ethernet Extender Module - 1 port 10/100/1000Base-T (RJ-45). BNC ( Coax ) Interlink ( VDSL2 ) connector
eX-1CM1110-TB - Managed Gigabit Ethernet Extender Module - 1 port 10/100/1000Base-T (RJ-45). 2-pin Terminal Block Interlink ( VDSL2 ) connector

Các bài viết tham khảo:

"BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!"

Downloads perle_ethernet_extenders_modules_installation_guide-bkaii.pdf