bkaii.com.vn BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!

SMI-1000-SFP: Managed Gigabit 1000Base-T to 1000Base-X Fiber Mode Conversion

Giá: Liên hệ

SMI-1000-SFP Managed Gigabit 1000Base-T to 1000Base-X Fiber Mode Conversion của hãng Perle hiện đang được BKAII phân phối rộng rãi tại thị trường Việt Nam. SMI-1000-SFP được thiết kế theo tiêu chuẩn công nghiệp, nhỏ gọn, dễ dàng lấy được tín hiệu về PLC, máy tính, vi xử lý, máy tính nhúng. Sản phẩm hiện đang được sử dụng trong các bài toán M2M, IoT của các lĩnh vực: Điện lực, khí tượng thủy văn, giao thông thông minh…

Bộ chuyển đổi Quang điện

Tính năng của sản phẩm:

1000Base-T to 1000Base-X Fiber SFP Media Converters
Empty slot for Cisco and other industry standard Gigabit Fiber SFPs
Manage via SNMP, CLI - Telnet/SSH, Internet Browser, or
PerleVIEW Centralized Management Package
Advanced media converter features - Smart Link Pass-Through, Fiber Fault Alert, Auto-MDIX and Loopback

Thông số kỹ thuật của sản phẩm:

Media Converter Module Indicators
Power / TST	This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.
Fiber link on / Receive activity (LKF)	This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-X interface has been taken down as a result of a fault on the 1000Base-T interface.
Copper link on / Receive activity (LKC)	This green LED is operational only when power is applied. The LED is on when the 1000Base-T link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-T interface has been taken down as a result of a fault on the 1000Base-T interface.
Management Module Indicators / reset
Power	Blinking green during startup cycle Steady green: module has power and is ready Red : error
ALM	Red alarm indicator activated when an alert event occurs
LKC	Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data
100/1000	Green - 1000 Mbps link Yellow - 100 Mbps link Off - 10 Mbps or no Link
Reset button	Recessed pinhole button resets module
Connectors
1000Base-T	RJ45 connector, 4 pair CAT5 UTP cable or better Magnetic Isolation 1.5kv
Small Form Factor Pluggable ( SFP ) slot	Empty slot for 1000Base-X SFP modules supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs. Hot insertion and removable ( hot swappable )
Management ethernet port	10/100/1000Base-T - RJ45 Auto- MDI/MDIX
Management console port	RS232 Serial RJ45 - Cisco pinout for use with standard CAT5 "rolled cable" (crossover) 9600 to 115k bps 7/8 bits Odd,even, no parity 1/2 stop bits Hardware/software flow control DCD/DSR monitoring
Packet Transmission Characteristics
Bit Error Rate (BER)	-12
Fiber Fault Alert	The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled Enabled (Default - Up) When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature. Disabled (Down)
Duplex	Full (Default-Up) - The media converter will advertise Full Duplex Capable, Half Duplex Capable. AUTO (Down) -The Media converter will advertise Full Duplex Not Capable, Half Duplex Capable.
Remote Loopback	The media converter can perform a loopback on the 1000Base-X fiber interface. (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface.
Configuration Mode Strap	Auto (default) enable management module to overwrite hardware switch settings Switch - Use on-board DIP switches
Power
Input Supply Voltage	( 12 vDC Nominal )
Current	0.42amps at 12vdc
Power Consumption	4.98 watts
Power Connector	5.5mm x 9.5mm x 2.1mm barrel socket
Power Adapter
Universal AC/DC Adapter	100-240v AC, regulated DC adapter included
Environmental Specifications
Operating Temperature	0° C to 50° C (32° F to 122° F)
Storage Temperature	minimum range of -25° C to 70° C (-13° F to 158° F)
Operating Humidity	5% to 90% non-condensing
Storage Humidity	5% to 95% non-condensing
Operating Altitude	Up to 3,048 meters (10,000 feet)
Heat Output ( BTU/HR )	17
MTBF (Hours)*	268,167 without power adaptor 178,770 with power adaptor
Chassis	Metal with an IP20 ingress protection rating
Mounting
Din Rail Kit	Optional
Wall / Rack Mount Kit	Optional
Product Weight and Dimensions
Weight	0.722 kg
Dimensions	175 x 145 x 23 mm
Packaging
Shipping Weight	1.2 kg
Shipping Dimensions	300 x 200 x 70 mm

Các bài viết tham khảo:

"BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!"

Downloads smi-installation-guide-bkaii.pdf