| Radio parameters |
RipEX |
RipEX2 |
| Frequency bands |
135–154; 154–174;
215-240;
300–320; 320–340; 340–360;
368–400; 400–432; 432–470; 470-512;
928–960 MHz |
135–175;
335-400;
400–470 MHz |
| Channel spacing |
6.25 / 12.5 / 25 / 50 kHz |
6.25 / 12.5 / 25 / 50 / 100 / 150 / 200 / 250 / 300 kHz |
| Frequency stability |
+/- 1.0 ppm |
| Modulation |
QAM (Linear): 16DEQAM, D8PSK, π/4DQPSK, DPSK
FSK (Exponential): 4CPFSK, 2CPFSK
|
QAM (Linear): 256QAM, 64QAM, 16DEQAM, D8PSK, π/4DQPSK, DPSK
FSK (Exponential): 4CPFSK, 2CPFSK |
| FEC (Forward Error Correction) |
On/Off, 3/4 |
On/Off, 2/3, 3/4, 5/6 |
| Anti-aliasing Selectivity |
50 kHz @ -3dB BW |
narrow/wide band SW selectable
56kHz @ -3dB BW applicable for 6.25/12.5/25kHz
500kHz @ -3dB BW applicable for 50/100/150/200kHz |
| Tx to Rx Time |
< 1.5 ms |
| Maximum Receiver Input Power |
20 dBm (100 mW) |
| Rx Spurious Emissions (Conducted) |
< -57 dBm |
| Radiated Spurious Emissions |
< -57 dBm |
| Blocking or desensitization |
detail |
-23dBm @ 1MHz
-19dBm @ 2MHz
-15dBm @ 5MHz
-13dBm @ 10MHz |
| Spurious response rejection |
> 70 dB |
|
| Electrical |
| Primary power |
10 to 30 VDC, negative GND |
| Rx |
5 W/13.8 V; 4.8 W/24 V; (Radio part < 2 W) |
8 W |
| Tx (dependent on RF power and modulation) |
13 – 40 W |
13 – 55 W |
| Sleep mode |
0.1 W |
0.01 W |
| Save mode |
2 W |
5 W |
|
| Interfaces |
| Ethernet |
1x 10/100 Base-T Auto MDI/MDIX / RJ45 |
4x 10/100/1000 Base-T Auto MDI/MDIX / RJ45 |
| SFP |
No |
1x 10/100/1000 Base-T/1000Base-SX/1000Base-LX |
| COM 1 |
RS232 / DB9F
300 – 115 200 bps |
RS232/RS485 SW configurable / DB9F
300 bps – 1 Mbps |
| COM 2 |
RS232/RS485 SW configurable / DB9F
300 – 115 200 bps |
mPCIe expansion board
GPS, 4G/3G/2G, 2x RS232 |
| USB |
USB 1.1 / Host A |
USB 3.0 / Host A |
| Antenna |
1x TNC female / 50 ohms (Rx/Tx) |
2x TNC female / 50 ohms
SW configurable: 1x Rx/Tx or 1x Rx + 1x Tx
|
| Inputs/Outputs |
1x HW alarm input
1x HW alarm output
1x Sleep input
|
1x HW alarm input
1x HW alarm output
1x Sleep input
2x DI, 2xDO, 1x difDI (when mPCIe-COMS is not used) |
|
| Indication LEDs |
| LED panel |
Power, ETH, COM1, COM2, Rx, Tx, Status |
SYS, AUX, RX, TX, COM |
| ETH |
No |
4x RJ45 – 2x LED, 1x SFP – 1x LED |
|
| Environmental |
| IP Code (Ingress Protection) |
IP40, IP51 |
IP42, IP52 |
| Hazardous locations |
Ex II 3G Ex ic IIC T4 Gc |
Pending |
| MTBF (Mean Time Between Failure) |
> 900.000 hours (> 100 years) |
| Operating temperature |
−40 to +70 °C (−40 to +158 °F) |
| Operating humidity |
5 to 95% non-condensing |
| Storage |
−40 to +85 °C (−40 to +185 °F) / 5 to 95 % non-condensing |
|
| Mechanical |
| Casing |
Rugged die-cast aluminium |
| Dimensions |
50 H x 150 W x 118 D mm (1.97 x 5.9 x 4.65 in) |
60 H x 185 W x 125 D mm (2.34 x 7.2 x 4.9 in) |
| Weight |
1.1 kg (2.4 lbs) |
1.55 kg (3.4 lbs) |
| Mounting |
DIN rail, L-bracket, Flat-bracket, 19″ Rack shelf |
|
| SW |
| Operating modes |
Bridge / Router |
Bridge / Router (+Switch) |
| User protocols on COM |
Modbus, IEC101, DNP3, PR2000, Comli, DF1, Profibus, Async Link, C24, Cactus, RP570, Slip, Siemens 3964(R)… |
| User protocols on Ethernet |
Modbus TCP, IEC104, DNP3 TCP, Comli TCP… |
| Serial to IP convertors |
Modbus RTU / Modbus TCP, DNP3 / DNP3 TCP, Terminal server |
| NTP |
Client, Server (synchronized from internal GPS) |
|
| Protocols on Radio channel |
| Different protocols for different applications |
Yes (Transparent, Flexible, Base driven) |
| Packet acknowledgement |
Yes |
| Data integrity control |
CRC 32 |
| Multi master applications |
Yes |
| Report by exception |
Yes |
| Collision Avoidance Capability |
Yes |
| Remote to Remote communication |
Yes |
| Addressed & acknowledged serial SCADA protocols |
Yes |
| Optimization |
Payload data and Ethernet / IP / TCP / UDP header compression, Packet flow on Radio channel optimization |
|
| Security |
| Management |
HTTP, HTTPS (own certificate), SSH |
| Access accounts |
2 levels (Guest, Admin) |
4 levels (Guest, Tech, SecTech, Admin) x 3 users |
| Encryption |
AES256 |
| IPsec |
Yes |
| VLAN |
Yes, IEEE 802.1Q |
| RADIUS |
No |
Yes |
| Firewall |
Layer 2 – MAC, Layer 3 – IP, Layer 4 – TCP/UDP |
| HW tamper |
No |
Yes |
|
| Diagnostics and Management |
| Radio link testing |
Yes (ping with RSS, Data Quality, Homogenity) |
Watched values
(Can be broadcast to neighbouring units. Received info displayed in Neighbours table) |
Device – Ucc, Temp, PWR, VSWR, (4)HW Alarm Input.
Radio channel – (4)RSScom, (4)DQcom, TXLost[%]
User interfaces – ETH[Rx/Tx], COM1[Rx/Tx], COM2[Rx/Tx] |
| Statistics |
For Rx/Tx Packets on User interfaces (ETH, COM1, COM2) and for User data and Radio protocol (Repeats, Lost, ACK etc.) on Radio channel |
| Graphs |
For Watched values and Statistics |
| History (Statistics, Neighbours, Graphs) |
20 periods (configurable, e.g. days) |
| SNMP |
SNMPv1, SNMPv2c, SNMPv3
SNMP Traps or SNMP Informs generation for Watched values |
| Monitoring |
Real time/Save to file analysis of all physical interfaces (RADIO, ETH, COM1, COM2) and some internal interfaces between software modules (e.g. Terminal servers, Modus TCP server etc.) |
|
| Standards |
| CE (RED), FCC, ATEX, RoHS |
| Spectrum |
ETSI EN 302 561 V2.1.1
ETSI EN 300 113 V2.2.1
FCC Part 90 |
ETSI EN 302 561 V2.1.1
ETSI EN 300 113 V2.2.1 |
| EMC (electromagnetic compatibility) |
ETSI EN 301 489-1 V2.1.1
ETSI EN 301 489-5 V2.1.1
IEC 1613:2009 Class 1 |
ETSI EN 301 489-1 V2.1.1
ETSI EN 301 489-4 V2.2.1 |
| Safety |
EN 60950-1:2006, A11:2009, A1:2010, A1:2010, A12:2011, A2:2013 |
EN 62368-1:2014 + A11:2017 |
| SAR |
EN 50385:2002
EN 50383ed.2:2010 |
EN 50385:2017
EN 50383ed.2:2010 |
| Vibration and shock |
EN 61373:1999
EN 60068-2-6:2008 |
Pending |
| Seismic qualification |
IEC 980:1989 (seismic category 1a) |
Pending |
| Hazardous locations |
EN 60079-0:2012
EN 60079-11:2012 |
Pending |
bkaii.com.vn
BKAII - Thiết bị truyền thông TỐT nhất với giá CẠNH TRANH nhất!
