IMF2100-1F(SSC20KM)-1DI(3IN1): 1x Fiber Ports + 1x RS-232/485/422 Serial to Fiber Modem

Fiber Port

Interface quantity: 1/2 (support ring network)

Fiber port: optional SC/FC/ST interface

Transmission distance:

lMultimode: 2km

lSingle mode: 20/40/60km

Transmission wavelength:

lMultimode: 1310nm

lSingle mode: 1310nm or 1550nm

Serial Port

Standard: EIA RS-232C, RS-485, RS-422

Serial port: 1 RS-232/485/422 serial port, can’t be used simultaneously

RS-232 signal: RXD, TXD, GND

RS-485 signal: D+, D-, GND

RS-422 signal: T+, T-, GND, R+, R-

Baud rate: 300~115200bps

Data bit: 5bit, 6bit, 7bit, 8bit

Stop bit: 1bit, 1.5bit, 2bit

Check bit: None, Even, Odd, Space, Mark

Interface type: 7-pin 3.81mm pitch terminal block

Direction control: RS-485 adopts automatic data flow control technology

Load capacity: RS-485 supports 32-point polling environment (128-point could be customized)

RS-485 pull up/down resistor: 4.7kΩ

RS-485 terminal resistance: built-in 120Ω, could be controlled by DIP switch

Transmission distance: RS-232 serial port, 15m；

RS-485/422 serial port, 1200m

Relay

Relay quantity: 1 relay alarm output

Connection method: 6-pin 5.08mm pitch terminal block(relay occupies 2 pins)

Current load: 1A@30VDC>, 0.3A@125VAC>

Default relay status: normally open

LED Indicator

Power Supply Indicator, Fiber Port Connection Indicator, Master/Slave Indicator, Alarm Indicator, Serial Port Data Receiving Indicator, Serial Port Data Sending Indicator

Power Requirement

Support four optional power solutions, 12~48VDC (single power supply), 12~48VDC (dual power supply), 110~370VDC or 85~265VAC

Solution 1

lPower supply range: 12~48VDC

lConnection method: 6-pin 5.08mm pitch terminal blocks (power supply occupies 4 pins)

lPower supply protection: built-in 2.0A over-current protection and non-polarity

lPower supply redundancy: support

Solution 2

lPower supply range: 12~48VDC

lConnection method: 6-pin 5.08mm pitch terminal blocks (power supply occupies 2 pins)

lPower supply protection: built-in 2.0A over-current protection and non-polarity

Solution 3

lPower supply range: 110~370VDC

lConnection method: 6-pin 5.08mm pitch terminal blocks (power supply occupies 2 pins)

lPower supply protection: built-in 2.0A over-current protection and non-polarity

Solution 4

lPower supply range: 85~265VAC

lConnection method: 6-pin 5.08mm pitch terminal blocks (power supply occupies 2 pins)

lPower supply protection: built-in 2.0A over-current protection

Power Consumption

No-load: ≤3.0W@24VDC>;

Full-load: ≤3.4W@24VDC>;

Environmental Limit

Operating temperature: -40~75℃

Storage temperature: -40~85℃

Relative humidity: 5%～95%(no condensation)

Physical Characteristic

Housing: IP40 protection, metal

Installation: DIN-Rail mounting

Weight: ≤360g

Dimension (W x H x D): 35mm×110mm×95mm

Industrial Standard

IEC 60950-1 / EN 60950-1: Safety

EN 55032: Conducted & Radiated Disturbances

IEC 61000-3-2 Harmonic Current Emission

IEC 61000-3-3 Voltage Fluctuation & Flicker

EN 55024

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-8

IEC 61000-4-11